Main information
Part Number	LC1D098F7C
Product Series	TeSys Deca
Product Series	TeSys Deca
product type	Contactor
product short name	LC1D
Application field of contactor	Applied to non-inductive or micro-inductive load, resistance furnace
use category	AC-1
number of poles	4P
Rated working voltage [Ue]	Power circuit: <= 690 V AC 25…400 Hz
Rated working voltage [Ue]	Power circuit: <= 225 V DC
Rated operating current [Ie]	20 A 60 °C) at <= 440 V AC AC-1 for power circuits
[Uc] control circuit voltage	110V AC 50/60Hz
Additional information
model	LC1D
Loop contact type	2 NO + 2 NC
protection cap	None
Conventional thermal current [Ith]	10 A at <60 °C for signal circuits
Conventional thermal current [Ith]	20 A at <60 °C for power circuits
Rated short-time withstand current [Icw]	105 A at <40 °C – 10 s for power circuit
	210 A at <40 °C – 1 s for power circuit
	30 A at <40 °C – 10 min for power circuit
	61 A at <40 °C – 1 minute for power circuit
	100 A – 1 s for signal circuit
	120 A – 500 ms for signal circuit
	140 A – 100 ms for signal circuit
Fuses for use with relays	10 A gG for signal circuits according to IEC 60947-5-1
	25 A gG at <= 690 V for power circuits type 1
	20 A gG for power circuits for type 2 at <= 690 V
average impedance	2.5 mΩ – Ith 25 A 50 Hz for power loop
Rated insulation voltage [Ui]	Power circuit: 690 V conforming to IEC 60947-4-1
Rated insulation voltage [Ui]	Signal circuit: 690 V conforming to IEC 60947-1
Overvoltage category	III
pollution level	3
Rated impulse withstand voltage [Uimp]	6 kV according to IEC 60947
Safety and reliability level	B10d = Contactor for 1369863 nominal loads according to EN/ISO 13849-1
Safety and reliability level	B10d = Contactor for 20000000 mechanical loads according to EN/ISO 13849-1
Mechanical life	15 Mcycles
Electrical life	0.6 Mcycles 25 A AC-1 at Ue <= 440 V
	2 Mcycles 9 A AC-3 at Ue <= 440 V
	2 Mcycles 6.6 A AC-3 at Ue at 660/690 V
Control loop characteristics	AC at 50/60 Hz
Surge Suppression Module	No built-in surge suppression module
Control voltage limit	0.3…0.6 Uc -40…60 °C release 50/60 Hz
	0.8…1.1 Uc -40…60 °C run 50 Hz
	0.85…1.1 Uc -40…60 °C run 60 Hz
(~50Hz pickup) power consumption (VA)	70 VA 60 Hz 0.75 20 °C)
(~50Hz pickup) power consumption (VA)	70 VA 50 Hz 0.75 20 °C)
(~50Hz hold) power consumption (VA)	7.5 VA 60 Hz 0.3 20 °C)
(~50Hz hold) power consumption (VA)	7 VA 50 Hz 0.3 20 °C)
heat dissipation	2…3 W at 50/60 Hz
action time	12…22 ms close
action time	4…19 ms break
operating frequency	3600 cycles/h at <60 °C
Wiring capacity	Power circuit: screw fastening1 1…4 mm² Lug O.D. Ø: 8 mm Cable option: flexible cord without wire terminal Power Circuit:
	screw fastening2 1…4 mm² Lug O.D. Ø: 8 mm Cable Selection: flexible cord without wire terminals
	Power circuit: screw fastening1 1…4 mm² Lug outer diameter Ø: 8 mm Cable selection: flexible cord with wire terminal Power
	circuit: screw fastening2 1…2.5 mm² Lug outer diameter Ø: 8 mm Cable option: flexible with wire terminals Power
	circuit: screw fastening1 1…4 mm² Lug outer diameter Ø: 8 mm Cable option: Solid without wire terminals Power
	circuit : Bolt fastening2 1…4 mm² Lug O.D. Ø: 8 mm Cable option: Rigid without wire terminals
	Control circuit: Bolt tight1 1…4 mm² Cable option: Flexible wire without wire terminals
	Control circuit: screw-on2 1…4 mm² Cable option: flexible without cable terminals
	Control circuit: screw-on1 1…4 mm² cable option: flexible with cable terminals
	Control circuit: screw-on2 1…2.5 mm² cable selection: flexible wire with wire terminals
	control circuit: screw fastened1 1…4 mm² cable selection: rigid without wire terminal
	control circuit: screw fastened2 1…4 mm² cable selection : Hard wire without wire terminal
Tightening torque	Power circuit: 1.7 Nm via screwdriver Ø 6 flat
	power circuit: 1.7 Nm via screwdriver No 2 Phillips screw
	control circuit: 1.7 Nm via screwdriver Ø 6 flat
	control circuit: 1.7 Nm via screw Screwdriver No. 2 for fastening Phillips screw
	Power circuit: 1.7 Nm Screwdriver Ø 6 flat-blade screw via cable connector: M3.5 Power circuit
	: 1.7 Nm Phillips screw driver No. 2 via cable connector Screw: M3.5
	Control circuit: 1.7 Nm Screwdriver pozidriv No 2 for screw tightening
	Power circuit: 1.7 Nm Screwdriver pozidriv No 2 for screw tightening
Auxiliary contact type	1 NO + 1 NC
Auxiliary contact type	Type Mechanical connection 1 NO + 1 NC conforming to IEC 60947-5-1
Auxiliary contact type	Type mirrored with main contact status 1 NC conforming to IEC 60947-4-1
Signal loop frequency	25…400Hz
Minimum switching voltage	17 V for signal return
Minimum switching current [Imin]	5 mA for signal loop
Insulation resistance	> 10 MΩ for signal loops
non-overlapping time	1.5 ms between de-energized NC and NO contacts
non-overlapping time	1.5 ms between energized NC and NO contacts
installation method	DIN rail installation
installation method	base plate installation
Environment
standard	GB 14048.4
standard	IEC 60947-4-1
certified product	CCC
	CE
	UKCA
IP protection class	IP2X front panel main circuit is suitable for screwed
IP protection class	IP2X front panel coil circuit is suitable for screwed
Protective measures	TH conforms to IEC 60068-2-30
ambient air temperature	-40…60 °C operation
	60…70 °C with derating
	-60…80 °C storage
working altitude	3000 m None
Fire resistance and abnormal high temperature resistance	850 °C conforming to IEC 60695-2-11
Shock and vibration resistance	Shock resistance with contacts open (2 gn (5…300 Hz)) conforming to IEC 60068-2-6 Shock resistance with contacts closed ( 4
	gn (5…300 Hz)) conforming to IEC 60068-2-6
	Shock performance 11 ms with contacts open (10 gn) conforming to IEC 60068-2-27
	Shock resistance 11 ms with contacts closed (15 gn) conforming to IEC 60068-2-27
high	85 mm
width	45 mm
depth	92 mm
product weight	0.365 kg
Packaging unit
Unit Type of Package 1	PCE
Number of Units in Package 1	1