Menu
Menu
$ 42.90 – $ 73.26
|
The beam-receiving photodiode and the A/D conversion circuit have been fabricated on a single chip optical IC (full custom). Hence, in spite of its miniature size, it has a performance and reliability which is equal to or better than the conventional product.
|
 |
|
The sensor incorporates a sensitivity adjuster in spite of its miniature size. It is convenient when you need fine adjustment. Further, the receiver of the thru-beam, side sensing type sensor incorporates an operation mode switch which can change the output operation.
|
 |
|
The EX-20 series achieves long distance sensing [thru-beam type: 2 m 6.562 ft, retroreflective type: 200 mm 7.874 in (when using the attached reflector), diffuse reflective type: 160 mm 6.299 in], despite its miniature size.
|
 |
|
The emission area of a dot light source is smaller than that of a conventional LED flat light source, and it is possible to design a high power, narrow beam. Since a red LED dot light source is used, the red beam spot is clear even at a far place, so that alignment and confirmation of sensing position is easy. Further, since the thru-beam type, too, incorporates a visible narrow beam, it can also reliably detect small parts, such as, chip components, lead frames, etc.
|
 |
|
The EX-20 series achieves reductions in power consumption of up to 65 %.
|
 |
The sensors features an IP67 rating to allow their use in process lines where water is used or splashed. Rust-resistant stainless steel sensor mounting brackets are available.
Note:If water splashes on the sensor during sensing operation, it may sense water as an object.
The EX-20 series become significantly stronger against inverter light and other extraneous light.
*Effective from production in April 2011.
|
Front sensing type of thru-beam type and diffuse reflective type sensors have identical appearance.
|
 |
|
It can be tightened with M3 screws. Moreover, metal inserts have been provided in the mounting holes so that the product is not damaged even in case of excess tightening.
|
 |
|
Universal sensor mounting bracket MS-EXL2-4 (for EX-22/23/26/28/29□) and MS-EX20-5 (for EX-23□ only) which can freely adjust the height and the angle of the sensor is available.
|
 |
|
Mounting of the front sensing type is possible from the rear side by using the mounting spacer.
|
 |
| Type | Thru-beam | Retroreflective | Diffuse reflective | ||
|---|---|---|---|---|---|
| Front sensing | Side sensing | Side sensing | Side sensing | ||
| Model No. (Note 2) |
Light-ON | EX-21A (-PN) |
EX-23 (-PN) (Note 3) |
EX-29A (-PN) |
EX-22A (-PN) |
| Dark-ON | EX-21B (-PN) |
EX-29B (-PN) |
EX-22B (-PN) |
||
| CE marking directive compliance | EMC Directive, RoHS Directive | ||||
| Sensing range | 1 m 3.281 ft |
2 m 6.562 ft |
30 to 200 mm 1.181 to 7.874 in (Note 4) |
5 to 160 mm 0.197 to 6.299 in (Note 5) with white non-glossy paper (200 x 200 mm) (7.874 x 7.874 in) |
|
| Sensing object | Min. ø2.6 mm ø0.102 in opaque object (Setting distance between emitter and receiver: 1 m 3.281 ft) |
Min. ø3 mm ø0.118 in opaque object (Setting distance between emitter and receiver: 2 m 6.562 ft) |
ø15 mm ø0.591 in or more opaque or translucent object (Note 4, 6) |
Opaque, translucent or transparent object (Note 6) |
|
| Hysteresis | – | 15 % or less of operation distance [200 x 200 mm 7.874 x 7.874 in (with white non-glossy paper)] | |||
| Repeatability (perpendicular to sensing axis) |
0.05 mm 0.002 in or less | 0.5 mm 0.020 in or less |
0.3 mm 0.012 in or less |
||
| Supply voltage | 12 to 24 V DC ± 10 % Ripple P-P 10 % or less | ||||
| Current consumption | Emitter: 10 mA or less, Receiver: 10 mA or less | 13 mA or less | |||
| Output | <NPN output type> NPN open-collector transistor ・Maximum sink current: 50 mA ・Applied voltage: 30 V DC or less (between output and 0 V) ・Residual voltage: 2 V or less (at 50 mA sink current) 1 V or less (at 16 mA sink current)<PNP output type> PNP open-collector transistor ・Maximum source current: 50 mA ・Applied voltage: 30 V DC or less (between output and +V) ・Residual voltage: 2 V or less (at 50 mA source current) 1 V or less (at 16 mA source current) |
||||
| Utilization category | DC-12 or DC-13 | ||||
| Short-circuit protection | Incorporated | ||||
| Response time | 0.5 ms or less | ||||
| Operation indicator | Orange LED (lights up when the output is ON) (thru-beam type: located on the receiver) |
||||
| Stability indicator | Green LED (lights up under stable light received condition or stable dark condition), located on the receiver |
Green LED (lights up under stable light received condition or stable dark condition) | |||
| Sensitivity adjuster | – | Continuously variable adjuster, located on the emitter |
Continuously variable adjuster | ||
| Operation mode switch | – | Located on the receiver | – | ||
| Pollution degree | 3 (Industrial environment) | ||||
| Protection | IP67 (IEC) | ||||
| Ambient temperature | -25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉ |
||||
| Ambient humidity | 35 to 85 % RH, Storage: 35 to 85 % RH | ||||
| Ambient illuminance | Incandescent light: 3,000 lx or less at the light-receiving face | ||||
| Voltage withstandability | 1,000 V AC for one min. between all supply terminals connected together and enclosure | ||||
| Insulation resistance | 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure | ||||
| Vibration resistance | 10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each | ||||
| Shock resistance | 500 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each | ||||
| Emitting element | Red LED (modulated) | ||||
| Peak emission wavelength | 640 nm 0.025 mil |
650 nm 0.026 mil |
680 nm 0.027 mil |
680 nm 0.027 mil |
|
| Material | Enclosure: Polyarylate, Lens: Polyarylate | ||||
| Cable | 0.1 mm2 3-core (thru-beam type sensor emitter: 2-core) cabtyre cable, 2 m 6.562 ft long | ||||
| Cable extension | Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable (thru-beam type: both emitter and receiver). | ||||
| Weight | Net weight (each emitter and receiver): 20 g approx. Gross weight: 60 g approx. |
Net weight: 20 g approx., Gross weight: 45 g approx. | |||
| Accessories | – | Adjusting screwdriver: 1 pc. |
RF-200 (Reflector): 1 pc. Adjusting screwdriver: 1 pc. |
Adjusting screwdriver: 1 pc. |
|
| Type | Convergent reflective | Narrow-view reflective | ||
|---|---|---|---|---|
| Diffused beam type | Small spot beam type | Long distance spot beam type | ||
| Front sensing | Side sensing | Side sensing | ||
| Model No. (Note 2) |
Light-ON | EX-24A(-PN) | EX-26A(-PN) | EX-28A(-PN) |
| Dark-ON | EX-24B(-PN) | EX-26B(-PN) | EX-28B(-PN) | |
| Sensing range | 2 to 25 mm 0.079 to 0.984 in (Conv. point: 10 mm 0.394 in) with white non-glossy paper (50 x 50 mm) (1.969 x 1.969 in) | 6 to 14 mm 0.236 to 0.551 in (Conv. point: 10 mm 0.394 in) with white non-glossy paper (50 x 50 mm 1.969 x 1.969 in), spot diameter ø1 mm ø0.039 in with setting distance 10 mm 0.394 in | 45 to 115 mm 1.772 to 4.528 in with white non-glossy paper (100 x 100 mm 3.937 x 3.937 in), spot diameter ø5 mm ø0.197 in with setting distance 80 mm 3.150 in | |
| Sensing object | Min. ø0.1 mm ø0.004 in copper wire (Setting distance: 10 mm 0.394 in) |
Min. ø0.1 mm ø0.004 in copper wire (Setting distance: 10 mm 0.394 in) |
Opaque, translucent or transparent object (Note 6) (Min. ø1 mm ø0.039 in copper wire at setting distance 80 mm 3.150 in) |
|
| Hysteresis | 15 % or less of operation distance [50 x 50 mm 1.969 x 1.969 in (EX-28□: 100 x 100 mm 3.937 x 3.937 in) (with white non-glossy paper)] | |||
| Repeatability (perpendicular to sensing axis) |
0.1 mm 0.004 in or less (Setting distance: 10 mm 0.394 in) |
0.05 mm 0.002 in or less (Setting distance: 10 mm 0.394 in) |
0.3 mm 0.012 in or less |
|
| Supply voltage | 12 to 24 V DC ± 10 % Ripple P-P 10 % or less | |||
| Current consumption | 13 mA or less | 15 mA or less | ||
| Output | <NPN output type> NPN open-collector transistor ・Maximum sink current: 50 mA ・Applied voltage: 30 V DC or less (between output and 0 V) ・Residual voltage: 2 V or less (at 50 mA sink current) 1 V or less (at 16 mA sink current)<PNP output type> PNP open-collector transistor ・Maximum source current: 50 mA ・Applied voltage: 30 V DC or less (between output and +V) ・Residual voltage: 2 V or less (at 50 mA source current) 1 V or less (at 16 mA source current) |
|||
| Utilization category | DC-12 or DC-13 | |||
| Short-circuit protection | Incorporated | |||
| Response time | 0.5 ms or less | |||
| Operation indicator | Orange LED (lights up when the output is ON) |
|||
| Stability indicator | Green LED (lights up under stable light received condition or stable dark condition) |
|||
| Sensitivity adjuster | – | Continuously variable adjuster | ||
| Operation mode switch | – | |||
| Pollution degree | 3 (Industrial environment) | |||
| Protection | IP67 (IEC) | |||
| Ambient temperature | -25 to +55 ℃ -13 to +131 ℉ (No dew condensation or icing allowed), Storage: -30 to +70 ℃ -22 to +158 ℉ |
|||
| Ambient humidity | 35 to 85 % RH, Storage: 35 to 85 % RH | |||
| Ambient illuminance | Incandescent light: 3,000 lx or less at the light-receiving face | |||
| Voltage withstandability | 1,000 V AC for one min. between all supply terminals connected together and enclosure | |||
| Insulation resistance | 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure | |||
| Vibration resistance | 10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each | |||
| Shock resistance | 500 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each | |||
| Emitting element | Red LED (modulated) | |||
| Peak emission wavelength | 680 nm 0.027 mil | 650 nm 0.026 mil | 650 nm 0.026 mil | |
| Material | Enclosure: Polyarylate, Lens: Polyarylate | |||
| Cable | 0.1 mm2 3-core cabtyre cable, 2 m 6.562 ft long | |||
| Cable extension | Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable. | |||
| Weight | Net weight: 20 g approx., Gross weight: 45 g approx. | |||
| Accessories | – | Adjusting screwdriver: 1 pc. | ||
Notes:
1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.
2) Model Nos. having the suffix “-PN” are PNP output type.
3) Either Light-ON or Dark-ON can be selected by the operation mode switch (located on the receiver).
4) The sensing range and the sensing object of the retroreflective type sensor are specified for the RF-200 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 30 mm 1.181 in away. However, if the reflector is set 100 mm 3.937 in or less away, the sensing object should be opaque.
|
5) In case of using this product at a sensing range of 50 mm 1.969 in or less, take care that the sensitivity adjustment range becomes extremely narrow.
6) Make sure to confirm detection with an actual sensor before use.
INOSAKI Limited
RM B 5/F Gaylord Comm,
Bldg 114-118 Lockhart Rd.
Hong Kong
INOSAKI Sdn. Bhd.
2-1-9, Ground Floor, One Square, Tingkat Mahsuri 1,
11900 Bayan Lepas, Penan
INOSAKI Pte. Ltd.
101 Upper Cross Street,
No. 06-17, People’s Park Centre,
Singapore (058357)
