SIMATIC S7-1500 – F Digital Output Module F-DQ 8x 24 V DC 2A PPM – Siemens Fail-Safe I/O Modules

$ 1,064.36

SKU: 6ES7526-2BF00-0AB0

Using fail-safe ET 200MP/S7-1500 modules makes it possible to implement safety-related application requirements as an integral part of the overall automation. The safety functions required for fail-safe operation are integrated in the modules. Communication with the fail-safe SIMATIC S7 CPUs is performed by means of PROFIsafe.

The modules can be operated both in centralized and distributed configurations.

Siemens Fail-safe Modules S7-1500 Product Specifications:

Article number 6ES7526-2BF00-0AB0
ET 200MP, F-DQ 8x24VDC 2A PPM
General information
Product type designation F-DQ 8x24VDC/2A PPM
Firmware version
● FW update possible Yes
Product function
● I&M data Yes; I&M0 to I&M3
Engineering with
● STEP 7 TIA Portal configurable/integrated from version V13 SP1 with HSP 0086
Operating mode
● DQ Yes
Supply voltage
Rated value (DC) 24 V
permissible range, lower limit (DC) 19.2 V
permissible range, upper limit (DC) 28.8 V
Reverse polarity protection Yes
Input current
Current consumption (rated value) 110 mA; without load
Current consumption, max. 130 mA; without load
output voltage / header
Rated value (DC) 24 V
Power
Power available from the backplane bus 0.8 W
Power loss
Power loss, typ. 11 W
Address area
Address space per module
● Inputs 6 byte; S7-300/400F CPU, 5 byte
● Outputs 6 byte; S7-300/400F CPU, 5 byte
Hardware configuration
Automatic encoding Yes
● Electronic coding element type F Yes
Digital outputs
Number of digital outputs 8
Current-sinking Yes
Current-sourcing Yes
Short-circuit protection Yes
Open-circuit detection Yes
● Response threshold, typ. 8 mA
Overload protection Yes
● Response threshold, typ. 2.9 A
Limitation of inductive shutdown voltage to PM-switching: -24 V + (-47 V), PP-switching: -24 V
Switching capacity of the outputs
● with resistive load, max. 2 A
● on lamp load, max. 10 W
Load resistance range
● lower limit 12 Ω
● upper limit 2 000 Ω
Output voltage
● for signal “1”, min. 24 V; L+ (-0.5 V)
Output current
● for signal “1” rated value 2 A
● for signal “0” residual current, max. 0.5 mA; Current-sourcing, or current sourcing and sinking switches individually, current sinking: max. 1 mA
Switching frequency
● with resistive load, max. 30 Hz
● with inductive load, max. 0.1 Hz
● on lamp load, max. 10 Hz
Total current of the outputs
● Current per channel, max. 2 A
Total current of the outputs (per module)
horizontal installation
— up to 40 °C, max. 16 A
— up to 60 °C, max. 8 A
vertical installation
— up to 40 °C, max. 8 A
Cable length
● shielded, max. 1 000 m
● unshielded, max. 500 m
Interrupts/diagnostics/status information
Diagnostics function Yes
Substitute values connectable No
Alarms
● Diagnostic alarm Yes
Diagnoses
● Monitoring the supply voltage Yes
● Wire-break Yes
● Short-circuit Yes
● Group error Yes
Diagnostics indication LED
● RUN LED Yes; green LED
● ERROR LED Yes; red LED
● Monitoring of the supply voltage (PWR-LED) Yes
● Channel status display Yes; green LED
● for channel diagnostics Yes; red LED
● for module diagnostics Yes; red LED
Potential separation
Potential separation channels
● between the channels No
● between the channels and backplane bus Yes
Isolation
Isolation tested with 707 V DC (type test)
Standards, approvals, certificates
Suitable for safety functions Yes
Highest safety class achievable in safety mode
● Performance level according to ISO 13849-1 PLe
● SIL acc. to IEC 61508 SIL 3
Probability of failure (for service life of 20 years and repair time of 100 hours)
— Low demand mode: PFDavg in accordance with SIL3 < 6.00E-05
— High demand/continuous mode: PFH in accordance with SIL3 < 2.00E-09 1/h
Ambient conditions
Ambient temperature during operation
● horizontal installation, min. 0 °C
● horizontal installation, max. 60 °C
● vertical installation, min. 0 °C
● vertical installation, max. 40 °C
Dimensions
Width 35 mm
Height 147 mm
Depth 129 mm
Weights
Weight, approx. 300 g

 

Weight 0.378 kg
Dimensions 15.1 × 15.2 × 4.7 cm

Related products