SIMATIC S7-1500 – TM Timer DIDQ 16x 24 V Time-Controlled Digital I/O Module – Siemens Technology Modules
$ 592.92
SKU: 6ES7552-1AA00-0AB0
Time-based IO modules read in switching edges at digital inputs with a high time resolution, and supply time information, as well as the status, to the CPU.
For the digital outputs, switching commands with additional time information are transferred from the CPU. The outputs switch at a pre-defined time.
The modules can be used for diverse applications requiring accuracy below the resolution of the PLC or bus cycle. This requires no more than storage of the relevant instructions in the controller.
The following time-based I/O modules are available:
- Timer DIDQ 16x24V
Time-controlled timer module with 8 inputs and 16 outputs, of which up to 16 with time stamp function; counter function up to 50 kHz, oversampling, pulse width modulation;
requires isochronous mode
Siemens Technology Modules S7-1500 Product Specifications:
Article number | 6ES7552-1AA00-0AB0 | |
S7-1500, TM Timer DIDQ 16x24V | ||
General information | ||
Product type designation | TM Timer DIDQ 16x24V | |
Product function | ||
● I&M data | Yes; I&M 0 | |
● Isochronous mode | Yes | |
Engineering with | ||
● STEP 7 TIA Portal configurable/integrated from version | V13 Update 3 | |
Installation type/mounting | ||
Rail mounting | Yes; S7-1500 mounting rail | |
Supply voltage | ||
Load voltage 1L+ | ||
● Rated value (DC) | 24 V | |
● permissible range, lower limit (DC) | 19.2 V | |
● permissible range, upper limit (DC) | 28.8 V | |
● Reverse polarity protection | Yes; against destruction | |
Load voltage 2L+ | ||
● Rated value (DC) | 24 V | |
● permissible range, lower limit (DC) | 19.2 V | |
● permissible range, upper limit (DC) | 28.8 V | |
● Reverse polarity protection | Yes; against destruction | |
Input current | ||
from load voltage 1L+ (without load), max. | 40 mA; without load | |
from load voltage 2L+ (without load), max. | 30 mA; without load | |
Encoder supply | ||
Number of outputs | 8; max. depending on parameterization | |
24 V encoder supply | ||
● 24 V | Yes; L+ (-0.8 V) | |
● Short-circuit protection | Yes | |
● Output current, max. | 1.2 A; Total current of all encoders / channels, max. 0.5 A per output | |
Power | ||
Power available from the backplane bus | 1.3 W | |
Power loss | ||
Power loss, typ. | 5 W | |
Address area | ||
Address space per module | ||
● Inputs | 44 byte | |
● Outputs | 74 byte | |
Digital inputs | ||
Number of digital inputs | 8; max. depending on parameterization | |
● in groups of | 8 | |
Digital inputs, parameterizable | Yes | |
Input characteristic curve in accordance with IEC 61131, type 3 | Yes | |
Digital input functions, parameterizable | ||
● Digital input with time stamp | Yes | |
— Number, max. | 8 | |
● Counter | Yes | |
— Number, max. | 4 | |
● Counter for incremental encoder | Yes | |
— Number, max. | 4 | |
● Digital input with oversampling | Yes | |
— Number, max. | 8 | |
● HW enable for digital input | Yes | |
— Number, max. | 4 | |
● HW enable for digital output | Yes | |
— Number, max. | 4 | |
Input voltage | ||
● Type of input voltage | DC | |
● Rated value (DC) | 24 V | |
● for signal “0” | -5 … +5 V | |
● for signal “1” | +11 to +30V | |
● permissible voltage at input, min. | -30 V; -5 V continuous, -30 V brief reverse polarity protection | |
● permissible voltage at input, max. | 30 V | |
Input current | ||
● for signal “1”, typ. | 2.5 mA | |
Input delay (for rated value of input voltage) | ||
● Minimum pulse width for program reactions | 3 µs for parameterization “none” | |
for standard inputs | ||
— parameterizable | Yes; none / 0.05 / 0.1 / 0.4 / 0.8 ms | |
— at “0” to “1”, min. | 4 µs; for parameterization “none” | |
— at “1” to “0”, min. | 4 µs; for parameterization “none” | |
Cable length | ||
● shielded, max. | 1 000 m; Depending on sensor, cable quality and rate of change | |
● unshielded, max. | 600 m; Depending on sensor, cable quality and rate of change | |
Digital outputs | ||
Type of digital output | Transistor | |
Number of digital outputs | 16; max. depending on parameterization | |
● in groups of | 8 | |
Current-sinking | Yes; With High Speed output | |
Current-sourcing | Yes | |
Digital outputs, parameterizable | Yes | |
Short-circuit protection | Yes; electronic/thermal | |
● Response threshold, typ. | 1.7 A with Standard output, 0.5 A with High Speed output | |
Limitation of inductive shutdown voltage to | -0.8 V | |
Controlling a digital input | Yes | |
Digital output functions, parameterizable | ||
● Digital output with time stamp | Yes | |
— Number, max. | 16 | |
● PWM output | Yes | |
— Number, max. | 16 | |
● Digital output with oversampling | Yes | |
— Number, max. | 16 | |
Switching capacity of the outputs | ||
● with resistive load, max. | 0.5 A; 0.1 A with High Speed output | |
● on lamp load, max. | 5 W; 1 W with High Speed output | |
Load resistance range | ||
● lower limit | 48 Ω; 240 ohm with High Speed output | |
● upper limit | 12 kΩ | |
Output voltage | ||
● Type of output voltage | DC | |
● for signal “0”, max. | 1 V; With High Speed output | |
● for signal “1”, min. | 23.2 V; L+ (-0.8 V) | |
Output current | ||
● for signal “1” rated value | 0.5 A; 0.1 A with High Speed output, observe derating | |
● for signal “1” permissible range, max. | 0.6 A; 0.12 A with High Speed output, observe derating | |
● for signal “1” minimum load current | 2 mA | |
● for signal “0” residual current, max. | 0.5 mA | |
Output delay with resistive load | ||
● “0” to “1”, max. | 1 µs; With High Speed output, 5 µs with Standard output | |
● “1” to “0”, max. | 1 µs; With High Speed output, 6 µs with Standard output | |
Switching frequency | ||
● with resistive load, max. | 10 kHz | |
● on lamp load, max. | 10 Hz | |
Total current of the outputs | ||
● Current per group, max. | 4 A | |
● Current per module, max. | 8 A; Observe derating | |
Cable length | ||
● shielded, max. | 1 000 m; depending on load and cable quality | |
● unshielded, max. | 600 m; depending on load and cable quality | |
Encoder | ||
Connectable encoders | ||
● Incremental encoder (asymmetrical) | Yes | |
● 24 V initiator | Yes | |
● 2-wire sensor | Yes | |
— permissible quiescent current (2-wire sensor), max. | 1.5 mA | |
Encoder signals, incremental encoder (asymmetrical) | ||
● Input voltage | 24 V | |
● Input frequency, max. | 50 kHz | |
● Counting frequency, max. | 200 kHz; with quadruple evaluation | |
● Cable length, shielded, max. | 600 m; Depending on input frequency, encoder and cable quality; max. 200 m at 50 kHz | |
● Incremental encoder with A/B tracks, 90° phase offset | Yes | |
● pulse encoder | Yes | |
Interface types | ||
● Input characteristic curve in accordance with IEC 61131, type 3 | Yes | |
Isochronous mode | ||
Bus cycle time (TDP), min. | 250 µs | |
Jitter, max. | 1 µs | |
Interrupts/diagnostics/status information | ||
Diagnostics function | Yes | |
Substitute values connectable | Yes | |
Alarms | ||
● Diagnostic alarm | Yes | |
Diagnoses | ||
● Monitoring the supply voltage | Yes | |
● Short-circuit | Yes | |
Diagnostics indication LED | ||
● RUN LED | Yes; green LED | |
● ERROR LED | Yes; red LED | |
● MAINT LED | Yes; Yellow LED | |
● Monitoring of the supply voltage (PWR-LED) | Yes; green LED | |
● Channel status display | Yes; green LED | |
● for channel diagnostics | Yes; red LED | |
Integrated Functions | ||
Counter | Yes | |
● Number of counters | 4 | |
● Counting frequency, max. | 200 kHz; with quadruple evaluation | |
Counting functions | ||
● Continuous counting | Yes | |
Position detection | ||
● Incremental acquisition | Yes | |
Potential separation | ||
Potential separation channels | ||
● between the channels and backplane bus | Yes | |
Isolation | ||
Isolation tested with | 707 V DC (type test) | |
Ambient conditions | ||
Ambient temperature during operation | ||
● horizontal installation, min. | 0 °C | |
● horizontal installation, max. | 60 °C | |
● vertical installation, min. | 0 °C | |
● vertical installation, max. | 40 °C; Observe derating | |
Altitude during operation relating to sea level | ||
● Installation altitude above sea level, max. | 5 000 m; restrictions for installation altitudes > 2 000 m, see ET 200MP system manual | |
Decentralized operation | ||
to SIMATIC S7-1500 | Yes | |
Dimensions | ||
Width | 35 mm | |
Height | 147 mm | |
Depth | 129 mm | |
Weights | ||
Weight, approx. | 320 g |
Weight | 0.436 kg |
---|---|
Dimensions | 16.1 × 19.2 × 4.2 cm |
Related products
-
Select options This product has multiple variants. The options may be chosen on the product page Details
-
Select options This product has multiple variants. The options may be chosen on the product page Details
-
Select options This product has multiple variants. The options may be chosen on the product page Details
-
Select options This product has multiple variants. The options may be chosen on the product page Details
-
Select options This product has multiple variants. The options may be chosen on the product page Details
-
Select options This product has multiple variants. The options may be chosen on the product page Details