Menu
Menu
$ 419.33
The IM 154-3 PN High Feature and IM 154-4 PN High Feature interface modules are responsible for the communication between the ET 200pro and higher-level controllers via PROFINET IO.
| Article number | 6ES7154-4AB10-0AB0 |
| ET 200pro, IM 154-4 PN HF | |
| General information | |
| Product type designation | IM 154-4 PN HF |
| Vendor identification (VendorID) | 0x002A |
| Device identifier (DeviceID) | 0x0305 |
| Supply voltage | |
| Rated value (DC) | 24 V |
| Reverse polarity protection | Yes; against destruction |
| Short-circuit protection | Yes; Fuse in lower part is exchangeable, the fuse on the IM-LP is not |
| power supply according to NEC Class 2 required | No |
| Load voltage 2L+ | |
| ● Rated value (DC) | 24 V |
| ● Reverse polarity protection | Yes; against destruction |
| Input current | |
| from supply voltage 1L+, max. | 400 mA; Dependent on terminal module, typ. maximum value for FO connection method, full load on RWB and 20.4 V input voltage |
| Power loss | |
| Power loss, typ. | 6 W; dependent on terminal module, typ. maximum value for CU connection method, full load on RWB, for FO the value is approx. 0.7 W higher |
| Address area | |
| Addressing volume | |
| ● Inputs | 256 byte |
| ● Outputs | 256 byte |
| Interfaces | |
| Interfaces/bus type | PROFINET IO |
| Interface types | |
| M12 port | |
| ● Autonegotiation | Yes |
| ● Transmission rate, max. | 100 Mbit/s |
| Protocols | |
| Protocols (Ethernet) | |
| ● SNMP | Yes |
| ● LLDP | |
| ● ping | Yes |
| ● ARP | Yes |
| Redundancy mode | |
| Media redundancy | |
| — MRP | Yes |
| Interrupts/diagnostics/status information | |
| Alarms | |
| ● Diagnostic alarm | Yes; Parameterizable |
| ● Hardware interrupt | Yes; Parameterizable |
| Diagnostics indication LED | |
| ● MAINT LED | Yes |
| ● LINK LED | Yes |
| ● RX/TX LED | Yes |
| ● For load voltage monitoring | Yes |
| ● Bus fault BF (red) | Yes |
| ● Group error SF (red) | Yes |
| ● Monitoring 24 V voltage supply ON (green) | Yes |
| Parameter | |
| Swapping interrupt | Parameterizable |
| Startup if setpoint not equal to actual configuration | Parameterizable |
| Hot swapping of modules | possible |
| Potential separation | |
| between backplane bus and electronics | No |
| between supply voltage and electronics | Yes |
| Isolation | |
| Isolation tested with | 707 V DC (type test) |
| Degree and class of protection | |
| IP degree of protection | IP65/67 |
| Ambient conditions | |
| Ambient temperature during operation | |
| ● min. | -25 °C |
| ● max. | 55 °C |
| Ambient temperature during storage/transportation | |
| ● min. | -40 °C |
| ● max. | 70 °C |
| Dimensions | |
| Width | 135 mm |
| Height | 130 mm |
| Depth | 60 mm |
| Weights | |
| Weight, approx. | 490 g |
| Weight | 0.536 kg |
|---|---|
| Dimensions | 14.2 × 16.4 × 7.4 cm |
INOSAKI Limited
RM B 5/F Gaylord Comm,
Bldg 114-118 Lockhart Rd.
Hong Kong
INOSAKI Sdn. Bhd.
2-1-9, Ground Floor, One Square, Tingkat Mahsuri 1,
11900 Bayan Lepas, Penan
INOSAKI Pte. Ltd.
101 Upper Cross Street,
No. 06-17, People’s Park Centre,
Singapore (058357)
