Control the output	Supply voltage	11PIN type	8PIN type
Output by Dot: DPDT (Time-limited output)	AC110V (50/60Hz)	H3BA-N AC110V	–
	AC220V (50/60Hz)	H3BA-N AC220V
	DC24V	H3BA-N DC24V
Output by Dot: Limited time SPDT with SPDT can be switched (Limited time ↔, instantaneous)	AC110V (50/60Hz)	–	H3BA-N8H AC110V
	AC220V (50/60Hz)		H3BA-N8H AC220V
	DC24V		H3BA-N8H DC24V

General

project	H3BA-N	H3BA-N8H
Action mode	A: ON Delay B: Flashing OFF Start B2: Flashing ON Start C: Signal ON/OFF Delay D: Signal OFF Delay E: Interval G: Signal ON/OFF Delay J: Monostable output	A: ON Delay H: ON Delay with Instantaneous Output Contact
Pin type	11pin	8pin
Input method	No voltage input	—
Output mode	DPDT (Limited Time)	SPDT (time-limited) vs. switchable SPDT (time-limited<—>instant)
Installation:	Aluminum rail mounting, surface mounting, and flush mounting
Applicable Standards	UL508, CSA C22.2 No.14, LR and CCC : GB/T 14048.5* according to EN 61812-1 (Pollution 2 / Overvoltage Category III)
EMC	(EMI) EN 61812-1 Radiological hazard intensity: EN 55011 class A AC power supply immunity: EN 55011 class A (EMS) EN 61812-1 Immunity to electrostatic discharge: EN 61000-4-2: 6kV contact discharge 8kV Air Discharge Radiated Radio Frequency: EN 61000-4-3: 10V/m (80MHz~1GHz AM modulation) Electric Field Strength Immunity: 3V/m (1.4GHz~2GHz AM Modulation) 1V/m (2GHz~2.7GHz AM modulation) 10V/m (900MHz pulse modulation) Conducted Noise Immunity: EN 61000-4-6: 10V (0.15MHz~80MHz) Radio Pulse Immunity: EN 61000-4-4: 2kV power cord 2kV I/O Signal Line Surge immunity: EN 61000-4-5: 2kV common mode 1kV Different Modes Voltage sag: EN 61000-4-11 Electrical shut-off immunity: EN 61000-4-11

*About CCC acquisition conditions

Proposed fuses	0216005 (250VAC, 5A) manufactured by Littelfuse
Rated operating voltage Ue Rated operating voltage Ie	AC-15: Ue: 250VAC, Ie: 3A AC-13: Ue: 250VAC, Ie: 5A DC-13: Ue: 30VDC, Ie: 0.1A
Rated insulation voltage	250V
Rated impulse voltage (Height: 2000m or less)	4kV (at AC240V)
Conditional short-circuit current	1,000A

Time frame

Units of time		s (seconds)	x 10s (10 seconds)	min (min)	x 10min (ten minutes)	h (hours)	x 10h (10 hours)
Full scale setting		s (seconds)	x 10s (10 seconds)	min (min)	x 10min (ten minutes)	h (hours)	x 10h (10 hours)
1.2	Set the time	0.05～1.2	1.2～12	0.12～1.2	1.2～12	0.12～1.2	1.2～12
3		0.3～3	3～30	0.3～3	3～30	0.3～3	3～30
12		1.2～12	12～120	1.2～12	12～120	1.2～12	12～120
30		3～30	30～300	3～30	30～300	3～30	30～300

Rated specifications

project	H3BA-N	H3BA-N8H
Rated supply voltage (Please refer to Notes 1 and 2)	AC110V (50/60Hz)、AC220V (50/60Hz)、DC24V
Voltage range of use (See Note 3)	85%~110% of rated power supply voltage
Power restoration	Minimum power on time: 0.1s
No voltage input	Impedance at ON: 1 kΩ or less Residual voltage at ON: 1 V or less Impedance at OFF: 200 kΩ or more
Power consumption	AC110V: Approx. 4.6VA (1.5W) AC220V: Approx. 7.6VA (1.3W) DC24V: Approx. 0.6W	AC110V: Approx. 3.6VA (1.6W) AC220V: Approx. 7.8VA (1.9W) DC24V: Approx. 0.9W
Control the output	Contact: 5A at 250V AC, resistive load (cosφ = 1)

Note 1. The DC ripple rate is less than 20%.

Note 2. Using models other than the DC24V H3BA-N type will generate a surge current.

When powering on these models through a contactless output such as a sensor, be aware of the surge current.

Note 3. If the timer is used continuously at high ambient temperatures, the DC standard ripple rate is 90% or higher.

Characteristic

project	H3BA-N	H3BA-N8H
Accuracy of action time	± 0.3% FS or less (±0.3% ±10ms in 1.2s range)
Setting error	±5% FS ±0.05s or less
Return time	Minimum power on time: 0.1s or less Minimum pulse input time: 50ms
Voltage effects	± 0.5% FS or less (±0.5% ±10ms in 1.2s range)
Temperature effects	±2% FS or less (±2% ±10ms in the 1.2s range)
Insulation resistance	100MΩ min. (at 500 VDC)
Withstand voltage	AC2,000V, 50/60Hz 1min (between conductive metal and exposed non-conductive metal) AC2,000V, 50/60Hz 1min (between control output terminal and operation circuit) AC1,000V, 50/60Hz 1min (between non-continuous contacts) (AC750V for H3BA-N8H type)
Impulse voltage	1kV (between power terminals) 2kV (between conductive terminals and exposed non-conductive metal parts, 1.5kV for DC24V type)
Noise resistant	Type AC: ± 1.5kV (between power terminals) and 600V (between input terminals) ± Square wave noise generated by noise simulator (pulse width: 100ns/1μs, 1ns rise) DC type: ± 480V (between power terminals), ± 600V (between input terminals). Square wave noise generated by the noise simulator (pulse width: 100ns/1μs, 1ns ramp)
Resistant to static electricity	Malfunction: 4kV Durability: 8kV
Vibration resistant	Durability: 10~55Hz, 0.75mm single amplitude, 3 directions, 1 time each Malfunction: 10~55Hz, 0.5mm single amplitude, 3 directions, 1 time each
Impact-resistant	Durability: 1,000 m/s2 (approx. 100 G), 3 directions, 1 time each Malfunction: 100 m/s2 (approx. 10 G), 3 directions, 1 time each
Ambient temperature	Operation: -10°C~55°C (no icing) Storage: -25°C~65°C (no freezing)
Ambient humidity	Operation: 35%~85%
Service life	Mechanical: 10,000,000 cycles or more (1,800 cycles/hour at no load) Electrical: 100,000 cycles or more (AC250V 5A Resistive Load, 1800 times/hour)	Mechanical: 10,000,000 cycles or more (1,800 cycles/hour at no load) Electrical: 100,000 cycles or more (AC250V 5A Resistive Load, 360 times/hour)
Housing color	Light grey (Munsell 5Y7/1)
Ingress protection	IEC: IP40 (panel surface)
weight	Approximately 95g