CS1W-NC[][]3 – Omron Position Control Units
USD $ 1,832.04
SKU: N/A
Basic Specifications
| Item | Model | ||
|---|---|---|---|
| CS1W-NC113/133 | CS1W-NC213/233 | CS1W-NC413/433 | |
| Power supply voltage |
5 VDC (for the PCU itself) | ||
| 24 VDC (external power supply) | |||
| 5 VDC (external power supply; line driver output only) | |||
| Allowable power supply voltage range |
4.75 to 5.25 VDC (for the PCU itself) | ||
| 21.6 to 26.4 VDC (external power supply) | |||
| 4.75 to 5.25 VDC (external power supply; line driver output only) | |||
| Internal current consumption |
250 mA max. at 5 VDC | 250 mA max. at 5 VDC | 360 mA max. at 5 VDC |
| Current consumption of external power supply |
NC113: 30 mA max. at 24 VDC NC133: 10 mA max. at 24 VDC NC133: 60 mA max. at 5 VDC |
NC213: 50 mA max. at 24 VDC NC233: 20 mA max. at 24 VDC NC233: 120 mA max. at 5 VDC |
NC413: 90 mA max. at 24 VDC NC433: 30 mA max. at 24 VDC NC433: 220 mA max. at 5 VDC |
| External dimensions |
130 (H) × 35 (W) × 101 (D) (all models) | ||
| Weight | 250 g max. | 250 g max. | 300 g max. |
| Safety standards | UL, CSA, EC (EMC Directive) | ||
Note: Specifications not listed above conform to CS Series general specifications.
Performance Specifications
| Item | Model | |||
|---|---|---|---|---|
| CS1W-NC113/133 | CS1W-NC213/233 | CS1W-NC413/433 | ||
| Applicable PLC models | CS-series PLCs | |||
| Unit type | CS1 Special I/O Unit | |||
| I/O requirements |
Words | 5 words | 10 words | 20 words |
| Slots | 1 slot | |||
| Controlled driver | Pulse-train input-type Servo Drive or stepping motor driver NC113/213/413 models have open collector output. NC133/233/433 models have line driver output. |
|||
| Control | Control system | Open-loop control by pulse train output | ||
| Number of control axes |
1 axis | 2 axes | 4 axes | |
| Control unit | Pulse | |||
| Positioning operations | Two types: memory operation and direct operation | |||
| Positioning operations |
Independent | 1 axis | 2 independent axes | 4 independent axes |
| Linear interpolation | None | 2 axes max. | 4 axes max. | |
| Speed control | 1 axis | 2 independent axes | 4 independent axes | |
| Interrupt feeding | 1 axis | 2 independent axes | 4 independent axes | |
| Positions | Range | – 1,073,741,823 to 1,073,741,823 pulses (See note.) | ||
| Data items | 100/axis | |||
| Speeds | Range | 1 pps to 500 Kpps | ||
| Data items | 100/axis | |||
| Acceleration and deceleration times |
Range | 0 to 250 s, until maximum speed is reached. | ||
| Data items | 9/axis for acceleration and deceleration each | |||
| Functions and settings |
Origin search | Origin proximity input signal: selectable (absent, N.O. or N.C. contact). Origin input signal: selectable (N.O. or N.C. contact) Origin compensation: – 1,073,741,823 to 1,073,741,823 pulses Origin search speed: High-speed or proximity-speed can be set. Origin detection method: May be set to stop upon origin input signal after proximity input signal has turned ON, to stop upon origin input signal after proximity input signal has turned OFF, to stop upon origin input signal without using proximity input signal, or to stop upon origin input signal after limit input signal has turned OFF. N.O. = Normally open N.C. = Normally closed |
||
| Jogging | Jogging can be executed at a specified speed. | |||
| Dwell times | 19/axis can be set from 0 to 9.99 s (unit: 0.01 s). | |||
| Acceleration/ deceleration curves |
Trapezoidal or S-curve (Can be set separately for each axis.) | |||
| Zones | Zone Flag turns ON when present position is within a specified zone. Three zones can be set for each axis. |
|||
| Software limits | Can be set within a range of – 1,073,741,823 to 1,073,741,823 pulses. | |||
| Backlash compensation |
0 to 9,999 pulses. Compensation speed can also be set. | |||
| Functions and settings |
Teaching | With a command from the PLC, the present position can be taken as the position data. |
||
| Deceleration stop | The STOP command causes positioning to decelerate to a stop according to the specified deceleration time. |
|||
| Emergency stop | Pulse outputs are stopped by an external emergency stop command. | |||
| Present position preset |
The PRESENT POSITION PRESET command can be used to change the present position to a specified value. |
|||
| Override | When the override enabling command is executed during positioning, the target speed is changed by applying the override coefficient. Possible to set to a value from 1 to 999% (by an increment of 1%) |
|||
| Data saving | 1) Saving to flash memory. (Can be written 100,000 times.) 2) Reading from PLC area by data reading instruction. 3) Reading by Support Tool and saving to personal computer hard disk or floppy disk. |
|||
| External I/O | Inputs | Prepare the following inputs for each axis: CW and CCW limit input signals, origin proximity input signal, origin input signal, emergency stop input signal, positioning completed signal, interrupt input signal |
||
| Outputs | Prepare the following outputs for each axis: Pulse outputs CW/CCW pulses, pulse outputs and direction outputs can be switched. Either error counter reset or origin-adjustment command outputs can be selected depending on the mode. |
|||
| Pulse output distribution period | 1-axis operation: 4 ms Linear interpolation: 8 ms |
|||
| Response time | Refer to Operation Manual Appendix A Performance Characteristics. | |||
| Self-diagnostic function | Flash memory check, memory loss check, CPU bus check | |||
| Error detection function | Overtravel, CPU error, software limit over, emergency stop | |||
Note: 1. The additional functions supported by Unit version 2.0 can be used only when the PCU is installed with a CS1-H
CPU Unit (either CPU Unit Ver. 2.0 or Pre-Ver. 2.0 CPU Unit). These functions cannot be used if the PCU is
installed with a CS1 CPU Unit (with -V1 suffix).
For details on Unit versions, refer to Unit Versions of CS-series Position Control Units on Operation Manual page
vi.
2. When performing linear interpolation, the distances that can be moved will vary.
| Weight | N/A |
|---|---|
| Model |
