Read carefully these safety instructions before installing and using the product. The producer is not responsible for damages and injury, which can occur due to false handling of the product and ignoring the safety instructions. All warranty will be spoiled in this case.
Intended use
IDS industrial cameras are to be used to capture images for visualization and image processing tasks. They are designed for use in industrial environments. Please comply with the requirements for the proper use of this product. Failure to do so will render the warranty void.
•The product is not authorized for use in security relevant applications. If it used in security relevant applications, the customer is responsible for the necessary approvals.
•If the product is modified or changed all approval becomes invalid. In this case, the customer is responsible for ensuring product conformity.
•The warranty expires if the product is improperly disassembled, reworked or repaired by the customer or a third party and IDS Imaging Development Systems GmbH assumes no liability for defects. If you need service, please contact the support team.
•This product is not suitable for use in locations where children are likely to be present.
Protection against electrostatic discharge (ESD)
Board-level cameras are especially sensitive to electrostatic discharge. Make sure to avoid mechanical or electrical damage of the printed circuit board or its connections. Wear ESD-protective clothing and observe the rules for handling ESD-sensitive components.
•Do not touch the printed circuit board while it is powered.
•Always hold the board by the edges to avoid the risk of electrostatic discharge damage.
•For optimum ESD behavior, a clearance of 4 mm from non-shielded housings has to be maintained all the way around. For shielded housings, a smaller clearance is possible.
•Attach the board to a conductive surface using the fixing screws. If this is not possible, ensure an insulating connection.
•Use connecting cable with a low-resistance shield on both sides.
Installation, operation and maintenance
The product has to be connected, taken into operation and maintained only by appropriately qualified personnel. The error-free and safe operation of this product can only be ensured if it is properly transported, stored, set up and assembled, and operated and maintained with due care. The installation, inspection, maintenance, extension, and repair may only be done by authorized personnel.
CAUTION! The housing of the camera is nickel-plated. Regular skin contact with nickel may cause a contact allergy. If you have a nickel allergy, skin contact with the housing may cause skin irritation. The symptoms may be delayed. Avoid prolonged skin contact with the camera housing. Wear gloves when handling the camera.
•Observe the specifications in the documentation when installing the product.
•Do not subject the product to direct sunlight, moisture or shock. Make sure that the IP code of the product meets the requirements for the ambient conditions.
•Only operate the product under ambient conditions for which the respective product is approved. The use under other ambient conditions may result in damage.
•To avoid any damage to the connectors, only mount or remove the product with the cables disconnected.
•Lay cables in such way that no one is endangered.
•Before starting up, check if the electrical wiring corresponds to the specifications in the documentation. Faulty wiring (overvoltage, undervoltage) can result in a damage in the electronics.
Transport
•Only use ESD packaging for storage and transport of ESD-sensitive components.
•Keep packing materials like films away from children. Abuse may result in suffocation.
Operation, power supply and I/O connections
The following components connected to the camera must meet the requirements for ES1 / maximum PS2 / LPS (Limited Power Source for Building wiring) / SELV (Safety Extra Low Voltage).
•Power supply / power adapter
•USB hub with external power supply
•Components connected to the I/O connections
•Ethernet / Power-over-Ethernet (PoE)
We recommend using a shielded connection cable or grounding the camera housing so that the camera housing is connected to ground via the appropriate installation.
WARNING! Non-approved power adapters for camera operation may cause painful or dangerous electric shock. Serious injury or death may occur. Use a power supply adapter that meets the requirements for ES1 / maximum PS2 / LPS (Limited Power Source for Building wiring) / SELV (Safety Extra Low Voltage).
WARNING! A USB hub with external power supply may cause painful or dangerous electric shocks. Serious injury or death may occur. Use a USB hub that meets the requirements for ES1 / maximum PS2 / LPS (Limited Power Source for Building wiring) / SELV (safety extra-low voltage).
Avis pour le Canada
Fonctionnement, alimentation électrique et connexions E/S
Les composants suivants connectés à la caméra doivent répondre aux exigences ES1 / PS2 maximum / LPS (Limited Power Source for Building wiring) / SELV (Safety Extra Low Voltage).
•Alimentation électrique / adaptateur d'alimentation
•Concentrateur USB avec alimentation externe
•Composants connectés aux connexions E/S
•Ethernet / Power-over-Ethernet (PoE)
Nous recommandons d'utiliser un câble de connexion blindé ou de mettre le boîtier de la caméra à la terre, de manière à ce que le boîtier de la caméra soit relié à la terre par l'installation appropriée.
AVERTISSEMENT ! Les adaptateurs d'alimentation non approuvés pour le fonctionnement de la caméra peuvent provoquer des chocs électriques douloureux ou dangereux. Des blessures graves, voire mortelles, peuvent survenir. Utilisez un adaptateur d'alimentation conforme aux exigences ES1 / PS2 maximum / LPS (Limited Power Source for Building wiring) / SELV (Safety Extra Low Voltage).
AVERTISSEMENT ! Un hub USB avec une alimentation externe peut provoquer des chocs électriques douloureux ou dangereux. Des blessures graves ou mortelles peuvent survenir. Utilisez un hub USB qui répond aux exigences ES1 / maximum PS2 / LPS (Limited Power Source for Building wiring) / SELV (Safety Extra Low Voltage).
CAUTION! As the camera housing may get hot depending on the operating conditions there may be risk of burns. Provide sufficient heat dissipation so that the housing temperature does not exceed 55 °C (131 °F).
NOTICE! Cameras with Power-over-Ethernet (PoE) can be powered from an external source or via PoE. The camera should not be supplied with both power sources at the same time, as this may cause irreparable damage to the camera.Correct disposal
Dispose the camera and accessories properly and separately from other types of waste to encourage recycling of reusable materials and to protect the environment.
According to the EC Directive 2012/19/EU (WEEE) we are obliged to take back this product, distributed by us after August 13, 2005, free of charge at the end of its useful life and to ensure it correct disposal. As this product is exclusively for commercial use (B2B), it must not be handed over to a public disposal facility. The product can be disposed of by specifying the date of purchase and the serial number at the following address:
IDS Imaging Development Systems GmbH
Dimbacher Str. 10
74182 Obersulm
