SIMATIC ET 200SP – Digital Special Fail-Safe Modules – Siemens Fail-Safe I/O Modules

$ 419.46

SKU: 6ES7136-6PA00-0BC0

The fail-safe ET 200SP modules can be used to implement the safety-related application requirements as an integrated part of the overall automation. The safety functions required for fail-safe operation are integrated in the modules. Communication with the fail-safe SIMATIC S7 CPUs is performed by means of PROFIsafe. The modules can be operated both in centralized and distributed configurations.

Siemens Fail-safe Modules SIMATIC ET 200SP Product Specifications:

Article number 6ES7136-6PA00-0BC0
ET 200SP, Powermod. F-PM-E PPM, 24V DC
General information
Product type designation F-PM-E 24 V DC/8 A PPM ST
usable BaseUnits BU type C0
Color code for module-specific color identification plate CC52
Product function
● I&M data Yes; I&M0 to I&M3
Engineering with
● STEP 7 TIA Portal configurable/integrated from version V12
● STEP 7 configurable/integrated from version V5.5 SP3 / –
● PROFINET from GSD version/GSD revision V2.31
Supply voltage
Rated value (DC) 24 V
permissible range, lower limit (DC) 20.4 V
permissible range, upper limit (DC) 28.8 V
Reverse polarity protection Yes
Input current
Current consumption (rated value) 75 mA; without load
Current consumption, max. 21 mA; From the backplane bus
output voltage / header
Rated value (DC) 24 V
Encoder supply
Number of outputs 2
Short-circuit protection Yes; Electronic (response threshold 0.7 A to 2.1 A)
Output current
● up to 60 °C, max. 0.3 A
24 V encoder supply
● 24 V Yes; min. L+ (-1.5 V)
● Short-circuit protection Yes
● Output current, max. 600 mA; Total current of all encoders
Power
Power available from the backplane bus 70 mW
Power loss
Power loss, typ. 5 W
Address area
Address space per module
● Inputs 7 byte
● Outputs 5 byte
Hardware configuration
Automatic encoding Yes
● Electronic coding element type F Yes
Digital inputs
Number of digital inputs 2
Source/sink input Yes; P-reading
Input characteristic curve in accordance with IEC 61131, type 1 Yes
Input voltage
● Type of input voltage DC
● Rated value (DC) 24 V
● for signal “0” -30 to +5 V
● for signal “1” +15 to +30 V
Input current
● for signal “1”, typ. 3.7 mA
Input delay (for rated value of input voltage)
for standard inputs
— parameterizable Yes
— at “0” to “1”, min. 0.4 ms
— at “0” to “1”, max. 20 ms
— at “1” to “0”, min. 0.4 ms
— at “1” to “0”, max. 20 ms
for technological functions
— parameterizable No
Cable length
● shielded, max. 1 000 m
● unshielded, max. 500 m
Digital outputs
Number of digital outputs 1
Short-circuit protection Yes
● Response threshold, typ. > 14.8 A
Open-circuit detection Yes
● Response threshold, typ. 8 mA
Overload protection Yes
● Response threshold, typ. 8.8 A
Limitation of inductive shutdown voltage to Max. -1.5 V
Switching capacity of the outputs
● with resistive load, max. 8 A
● on lamp load, max. 100 W
Load resistance range
● lower limit 3 Ω
● upper limit 2 000 Ω
Output voltage
● for signal “1”, min. 24 V; L+ (-0.5 V)
Output current
● for signal “1” rated value 8 A
● for signal “0” residual current, max. 1.5 mA; PP-switching: max. 1.5 mA; PM-switching: max. 1 mA
Switching frequency
● with resistive load, max. 10 Hz; Symmetrical
● with inductive load, max. 0.1 Hz; according to IEC 60947-5-1, DC-13, symmetrical
● on lamp load, max. 4 Hz; Symmetrical
Total current of the outputs
● Current per channel, max. 8 A; note derating data in the manual
● Current per module, max. 8 A; note derating data in the manual
Cable length
● shielded, max. 1 000 m
● unshielded, max. 500 m
Interrupts/diagnostics/status information
Diagnostics function Yes; See Chapter “Alarms/diagnostic messages” in the manual
Substitute values connectable No
Alarms
● Diagnostic alarm Yes
● Hardware interrupt No
Diagnostics indication LED
● RUN LED Yes; green LED
● ERROR LED Yes; red LED
● Monitoring of the supply voltage (PWR-LED) Yes; green PWR LED
● Channel status display Yes; green LED
● for channel diagnostics Yes; red LED
● for module diagnostics Yes; green/red DIAG LED
Potential separation
Potential separation channels
● between the channels No
● between the channels and backplane bus Yes
● between the channels and the power supply of the electronics No
Isolation
Isolation tested with 707 V DC (type test)
Standards, approvals, certificates
Suitable for safety functions Yes
Highest safety class achievable in safety mode
● Performance level according to ISO 13849-1 PLe
● SIL acc. to IEC 61508 SIL 3
Ambient conditions
Ambient temperature during operation
● horizontal installation, min. 0 °C
● horizontal installation, max. 60 °C
● vertical installation, min. 0 °C
● vertical installation, max. 50 °C
Dimensions
Width 20 mm
Height 73 mm
Depth 55 mm
Weights
Weight, approx. 70 g
Weight 0.081 kg
Dimensions 6.7 × 7.5 × 2.9 cm

Related products